NF G07-137-1-2001 纺织品.织物外观的评定.第1部分:织物在洗涤和干燥后耐油脂性处理的评定
作者:标准资料网 时间:2024-05-22 01:24:17 浏览:9681
来源:标准资料网
【英文标准名称】:Textiles-Assessmentoftheappearanceoffabrics-Part1:assessmentofthe"crease-resistant"treatmentoffabricsafterwashinganddrying.
【原文标准名称】:纺织品.织物外观的评定.第1部分:织物在洗涤和干燥后耐油脂性处理的评定
【标准号】:NFG07-137-1-2001
【标准状态】:现行
【国别】:法国
【发布日期】:2001-04-01
【实施或试行日期】:2001-04-05
【发布单位】:法国标准化协会(FR-AFNOR)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:Comparison;Fabrics;Householdlinen;Standardmeasures;Textiles;Washingtests
【摘要】:
【中国标准分类号】:W04
【国际标准分类号】:59_080_30
【页数】:6P.;A4
【正文语种】:其他
【英文标准名称】:Industrial-processcontrolvalves-Controlvalveterminologyandgeneralconsiderations
【原文标准名称】:工业过程控制阀.控制阀术语和一般考虑
【标准号】:BSEN60534-1-2005
【标准状态】:现行
【国别】:英国
【发布日期】:2005-03-31
【实施或试行日期】:2005-03-31
【发布单位】:英国标准学会(BSI)
【起草单位】:BSI
【标准类型】:()
【标准水平】:()
【中文主题词】:安全部件;过程测量和控制技术;术语;阀门;过程控制;试验;电气工程;方向控制阀;名称与符号;定义;控制阀
【英文主题词】:Classification;Commonterms;Controlvalves;Definition;Definitions;Designations;Dimensioning;Direction-controlvalves;Electricalengineering;Englishlanguage;Flowcapacity;Flowrates;Generalsection;Industries;Processcontrol;Processmeasuringandcontroltechnology;Safetycomponents;Terminology;Testing;Valves
【摘要】:ThispartofIEC60534appliestoalltypesofindustrial-processcontrolvalves(hereinafterreferredtoascontrolvalves).ThispartestablishesapartialbasicterminologylistandprovidesguidanceontheuseofallotherpartsofIEC60534.
【中国标准分类号】:N16
【国际标准分类号】:01_040_23;23_040_60
【页数】:16P.;A4
【正文语种】:英语
Product Code:SAE J737
Title:Hole Spacing for Scraper and Dozer Cutting Edges (Cancelled Aug 2007, Superseded by ISO 7129)
Issuing Committee:Mtc1, Loaders, Crawlers, Scrapers And Mounted Attachments
Scope:This standard is intended for cutting edge sections used on:a. Tractor-scrapers as described in SAE J1057 and J728b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted.This standard specifies hole placement along with length and width of the cutting edge.